Siemens SIMATIC IPC627C Provozní pokyny Strana 67
- Strana / 210
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Expansion and parameter assignment
10.2 Memory expansion
SIMATIC IPC627C
Operating Instructions, 11/2010, A5E02669068-02
67
Preparation
Disconnect the device from mains and unplug all cables.
CAUTION
The electronic components on the PCBs are highly sensitive to electrostatic discharge.
Always take appropriate precautionary measures when handling these components. Refer
to the ESD directives on handling electrostatic sensitive components.
NOTICE
We highly recommend using memory modules approved by Siemens. Siemens disclaims
any liability for impairment of functions caused by the use of third-party memory modules.
Installing a memory module
How to install a memory module
1 Open the device (Page 65).
2
Note where the (polarized) cutout ①
is located on the pin side of the RAM
module before inserting it.
3 Insert the module downwards,
applying slight pressure and press it
until the locking snaps into place.
4 Close the device.
Removing a memory module
How to remove a memory module
1 Open the device.
2 Release the locking mechanism on
the left and right.
3 Pull the memory module out of the slot.
4 Close the device.
- SIMATIC IPC627C 1
- SIMATIC 1
- Industrial PC 1
- Table of contents 3
- Table of contents 5
- Introduction 10
- Safety notes 11
- Battery 12
- ESD directives 12
- Description 13
- 3.2 Areas of application 14
- 3.3 Benefits 14
- 3.4 Function 15
- 3.5 Features 15
- 3.5 Features 16
- Description 17
- 3.5 Features 17
- 3.7 Design 19
- 3.7 Design 20
- 3.7.2 Operator Controls 21
- On/off button 22
- Interfaces 23
- AC power supply 25
- DC power supply 25
- 6)352),1(7 26
- Status display 27
- Application planning 29
- Rating plate 30
- COA label 30
- Application planning 31
- Mounting 33
- Mounting 35
- Connecting 37
- Localized information 39
- ①, if necessary 40
- ① DC 24 V 41
- ② ground 41
- ③ protective conductor 41
- ① to the device 42
- Commissioning 45
- Switch off the device 46
- 7.5 Notes on operation 47
- 7.5 Notes on operation 48
- Commissioning 49
- 7.5 Notes on operation 49
- Comments about faults 50
- Characteristics 53
- Booting from the Flash drive 53
- Integration 55
- 8.2 PROFINET 56
- Further information 57
- 8.2 PROFINET 58
- Functions 59
- 9.2 Temperature monitoring 60
- 9.3 Watchdog (WD) 60
- 9.4 Fan monitoring 61
- 9.5 Status display 61
- 9.6 SRAM buffer memory 62
- 9.7 Battery monitoring 62
- Function 63
- Requirements 63
- Configuration of the AMT PC 63
- 10.1 Opening the Device 65
- 10.2 Memory expansion 66
- Preparation 67
- Installing a memory module 67
- Removing a memory module 67
- Inserting the slider 69
- 10.4 Installing drives 70
- Preparations 71
- ① on the DVD 72
- ① the drive 73
- ① of the 73
- Installing an SSD drive 74
- Memory expansion options 75
- Opening the board slot 75
- ① and remove 78
- Service and maintenance 81
- Disposal 82
- Replacing the battery 83
- Reconfiguring the BIOS setup 84
- ① from the 85
- ① on the bus 86
- ②. Remove the 87
- Removing the fan 90
- ① on the 91
- Recovery CD or DVD: 92
- Restore DVD: 92
- 11.2.3 Installing Windows 93
- Setting up partitions 94
- Service and maintenance 95
- Drivers & Updates 98
- 11.2.9 Update installation 99
- 11.2.11 CP 1616 onboard 100
- 11.4 BIOS update 101
- 11.5 BIOS Recovery 102
- 12.1 Boot error messages 103
- 12.2 BIOS beep codes 103
- 12.2 BIOS beep codes 104
- 12.2 BIOS beep codes 105
- Special codes 109
- Troubleshooting/FAQs 111
- 13.1 General problems 112
- Troubleshooting/FAQs 113
- Technical data 115
- 14.1 General Specifications 116
- Technical data 117
- Maximum current values 119
- Typical power values 119
- 14.3 AC voltage supply 120
- 14.4 DC power supply 121
- 14.4 DC power supply 122
- Dimension drawings 123
- Dimension drawings 125
- Detailed descriptions 129
- 16.1 Motherboard 130
- Detailed descriptions 131
- 16.1 Motherboard 131
- 16.1.4 External ports 133
- PROFIBUS/MPI interface X4 134
- /(' /(' 135
- DVI-I port, X70 136
- Compact Flash card, X50 137
- 16.1.5 Internal interfaces 138
- 16.1.6 Front ports 140
- Display interfaces 141
- 16.2 Bus board 144
- 16.2 Bus board 145
- 16.2 Bus board 146
- 16.3 System resources 147
- 16.3 System resources 148
- 16.3 System resources 149
- 16.4 BIOS-Setup 153
- Menu layout 154
- 16.4.4 Main menu 155
- 16.4.5 Advanced menu 156
- 16.4 BIOS-Setup 157
- 16.4 BIOS-Setup 158
- Settings in the BIOS 162
- Settings in the MEBx 162
- ME general settings 163
- AMT configuration 164
- 16.4.7 Security menu 165
- 16.4.8 Power menu 166
- 16.4.9 Boot Menu 167
- 16.4.10 Version Menu 170
- 16.4.11 Exit menu 171
- BIOS Setup default settings 172
- 16.5.1 Overview of AMT 175
- 16.5.3 Advanced settings 176
- Procedure 177
- 16.5.6 Forcing user consent 178
- 16.6.1 Introduction 178
- Ethernet 179
- Three RJ45 connectors 179
- CP 1616 onboard as IO device 180
- Firmware 180
- Installation 181
- Loader files 181
- 16.6.2.1 Loading firmware 181
- Start downloading procedure 181
- Example 182
- Configuring 182
- Appendix 183
- ISO 9001 certificate 184
- Software License Agreement 184
- Product safety 184
- A.3 Service and support 185
- A.3 Service and support 186
- ESD guidelines 187
- List of abbreviations 189
- C.1 Abbreviations 190
- List of abbreviations 191
- C.1 Abbreviations 191
- Glossary 195
- Glossary 197
- SIMATIC IPC627C 208
- Index 209
Související produkty a manuály pro Barebones pro PC / pracovní stanice Siemens SIMATIC IPC627C
(238 stránky)
(52 stránky)
(276 stránky)
(80 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce