Siemens COM32 Uživatelská příručka Strana 18
- Strana / 126
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Introduction ION Setup User Guide
Page 18 © 2010 Schneider Electric. All rights reserved.
In order to avoid communications issues:
Baud rate, protocol and data format settings need to be the same for all the
connected serial devices.
Each serial device must have a unique Unit ID.
The gateway device must have the same baud rate and data format settings as
the connected serial devices, if these can be configured.
EGX series considerations
The PowerLogic™ EGX series Ethernet gateway can provide Ethernet access to
multiple RS-485 devices that are connected to the EGX’s RS-485 port. After wiring
the RS-485 devices to the EGX, use a web browser to log in to the EGX. Browse
to the device list page and enter each device that is connected to the EGX’s
RS-485 port. Set the appropriate device address and device type for each device.
Refer to the EGX Series Installation Guide.
After you add the devices to the EGX’s web page, you must add an Ethernet
gateway site to ION Setup and then add those devices to the gateway site. See
“Adding and Configuring Devices” on page 41 for more information.
PM8ECC considerations
Similar to the EGX series gateway, the PM8ECC Ethernet communications card
provides Ethernet access to multiple RS-485 devices that are connected to the
PM8ECC’s RS-485 port. After wiring the RS-485 devices to the PM8ECC, use a
web browser to log in to the PM8ECC. Browse to the device list page and enter
each device that is connected to the PM8ECC’s RS-485 port. Set the appropriate
device address and device type for each device. Refer to the PM8ECC Installation
Guide.
After you add the devices to the web page, you must add an Ethernet gateway site
to ION Setup and then add those devices to the gateway site. See “Adding and
Configuring Devices” on page 41 for more information.
ION meter EtherGate considerations
When an Ethernet-capable ION meter has EtherGate enabled, a workstation using
ION Setup software can communicate through the meter to a serial device (or
devices) wired to the appropriate serial communications port of the EtherGate-
enabled meter.
When you configure the EtherGate-enabled meter (in addition to the general
settings listed above), the protocol for the serial communications port must be set
to EtherGate
For more information on using your meter as an EtherGate, refer to the gateway
meter’s documentation and the technical note The ION Meter as an Ethernet
Gateway.
NOTE
To connect to and read data from your EtherGate meter, in addition to the serial devices, add it as a
stand-alone Ethernet meter in ION Setup. See “Adding a New Meter” on page 53.
- PowerLogic ION Setup 2.2 1
- Terminology 3
- Contents 5
- Chapter 1 Introduction 7
- ION Setup Features 8
- System Requirements 9
- Overview 10
- Getting More Information 11
- Installing ION Setup 12
- Communicating with Devices 13
- Connecting to serial devices 14
- Using Modem Communications 15
- Using Ethernet Communications 16
- List of Common Procedures 20
- Starting ION Setup 22
- Using the Network Viewer 26
- Left and right panes 27
- ION Setup Commands 28
- Menu Command Effect 29
- Viewing Options 31
- Viewing the unassigned group 32
- Basic versus Advanced Mode 33
- Setting Up Options 34
- Confirmation tab 35
- Security tab 35
- Conventions tab 37
- Applying Security 38
- Working in Single Device Mode 44
- Using Serial Communications 45
- Using Offline Programming 46
- Working in Network Mode 48
- Adding and Configuring Sites 49
- IP Port Description 52
- Adding a New Meter 53
- Grouping Devices 54
- Assigning a Device to a Group 55
- Editing Site Properties 55
- Editing Group Properties 58
- Editing Meter Properties 58
- Description 59
- Setup Screen Examples 62
- Example 3 63
- Example 4 63
- Overview of ION Architecture 66
- Creating new ION modules 67
- Linking ION modules 68
- ION Meter Cloning 72
- In this Chapter 73
- Setup Assistant Overview 74
- Template Screen 75
- Template Paste options 76
- Basic Setup Screen 77
- Security Screen 78
- Communications Screens 81
- 3rd Party Protocols Screen 81
- Clock Screen 83
- Demand Screen 84
- Input / Output Screens 84
- LED Pulsing Screen 85
- Energy Pulsing Screen 85
- OnBoard Digital Inputs Screen 86
- Analog Outputs Screen 86
- Memory Screen 87
- Event Log Screen 89
- EnergyDemand Log Screen 90
- Configuring Interval/Depth 91
- PT/CT Correction Screen 92
- Transformer Loss Screen 92
- Time of Use (TOU) Screen 93
- Sunday--and click OK 96
- Alarming Screen 98
- Power Quality Screen 99
- Displays Screen 99
- The Display Editor appears 100
- Verification Screen 101
- Phasor Viewer 103
- Reports Screen 104
- Writing to Multiple Registers 107
- In this chapter 109
- Displaying Data 110
- Closing data screens 111
- Performing Control Operations 112
- Chart Plotting 113
- Editing chart properties 114
- Chapter 6 Troubleshooting 117
- Troubleshooting ION Setup 118
- ION Setup Diagnostics Tools 119
- Troubleshooting Devices 122
- PowerLogic™ ION™ Setup 126
- User Guide 126
- Schneider Electric 126
Související produkty a manuály pro Software Siemens COM32
Software Siemens SIMATIC NET Uživatelská příručka
(68 stránky)
(68 stránky)
Software Siemens Simatic S7-300 Uživatelský manuál
(26 stránky)
(26 stránky)
Software Siemens SIMATIC NET Specifikace
(268 stránky)
(268 stránky)
Software Siemens v1.0 Servisní příručka
(202 stránky)
(202 stránky)
Software Siemens 270 series Provozní pokyny
(274 stránky)
(274 stránky)
Software Siemens S7-400 Servisní příručka
(382 stránky)
(382 stránky)
Software Siemens AC65 Uživatelská příručka
(123 stránky)
(123 stránky)
Software Siemens Simatic M7-400 Uživatelský manuál
(266 stránky)
(266 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce