Siemens Sinumerik 810T Uživatelský manuál stáhnout pdf (Strana 9)

EMCO WINNC SINUMERIK 810/820 T

A 5

KEY DESCRIPTION

Spindel stop / spindle start; spindle start in JOG and INC1...INC10000 mode:

Clockwise: perss key short, Counterclockwise: press min. 1 sec.

Open / close door

Close / open clamping device

Tailstock back / forward

Swivel tool holder

Coolant / puff blowing on / off

AUX OFF / AUX ON (auxiliary drives off / on)

Mode selector

Feed / rapid feed override switch

EMERGENCY OFF (Unlock: pull out button)

Key switch for special operations (siehe Maschinenbeschreibung)

Additional NC start key

Additional key clamping device

Consent key





No function

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 89 90

Software Description 1
Contents 3
E: @-Codes 4
G: Survey Pages 4
H: Alarms and Messages 4
Starting Information 4
A: Key Description 5
Key functions 6
Address and Numeric Keyboard 6
Machine Control Keys 8
KEY DESCRIPTION 9
PC Keyboard 10
Screen with Softkeys 11
INNC SINUMERIK 810/820 T 12
EY DESCRIPTION 12
B: Basics 13
Zero Offset 14
Coordinate System 14
Input of the 15
Tool Data Measuring 16
Cutter position 17
Input of the Tool Data 18
Tool Data Measuring with the 20
Optical Presetting Device 20
C: Operating Sequences 21
Approach the Reference Point 22
Input of the Gear Position 22
Setting of Language and 22
Workpiece directory 22
Input of Programs 23
PERATING SEQUENCES 24
Program Administration 25
Data Input-Output 25
Program Run 29
Graphic simulation 31
D: Programming 33
Survey of G Commands 34
Survey of M Commands 34
Survey of Cycles 34
Description of G Commands 35
G01 Linear Interpolation 35
G02 Circular Interpolation 36
Clockwise 36
G03 Circular Interpolation 36
Counterclockwise 36
G04 Dwell 37
G09 Exact Stop 37
G10 - G13 Polar Coordinate 37
Interpolation 37
G25/G26 Programmable working 38
G33 Thread Cutting 39
Cutter Radius Compensation 39
ROGRAMMING 40
G48 Leave as Approached 42
G50 Cancel Scale Modification 42
G51 Scale Modification 42
G54 - G57 Zero Offset 1 - 4 43
G58/G59 Programmable Zero 43
G60 Exact Stop Mode 44
G63 Thread tapping with 44
G70 Measuring in Inches 45
G71 Measuring in Millimetre 45
G92 Spindle Speed Limit 46
G90 Absolute Programming 46
G91Incremental Programming 46
G94 Feed per Minute 49
G95 Feed per Revolution 49
G96 Constant Cutting Speed 49
G97 Constant Spindle Speed 49
G131 Transmit 50
Description of Cycles 55
L93 Cut-in Cycle 55
L94 Undercut Cycle 56
L97 Thread Cutting Cycle 58
L971 Longitudinal Thread 58
L98 Deep Hole Drilling Cycle 59
L99 Thread Draft 60
Contour definition 61
Subroutines 63
R PARAMETER 71
OFFSET" 73
Softkey Menu Survey 74
Survey Guiding 76
Control Alarms 78
Machine Alarms 85

Komentáře k této Příručce

Žádné komentáře

Siemens Sinumerik 810T Uživatelský manuál Strana 9

Komentáře k této Příručce

Související produkty a manuály pro Sítě Siemens Sinumerik 810T