Siemens ET 757 E Series Provozní pokyny stáhnout pdf (Strana 61)

Configuration / project engineering

5.3 Configuring the communication

ET 200pro FC

Operating Instructions, 11/2007, A5E01100763B AA

Figure 5-3 Allocating the slave address at the PROFIBUS DP

The configuration should now appear as follows:

Figure 5-4 Configuration

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 189 190

ET 200pro FC 1
Product Information 2
SIMATIC ET 200S FC 2
SIMATIC ET 200pro FC 2
SIMATIC 3
Frequency converters 3
Foreword 5
Validity of the manual 6
Experience required 6
Recycling and disposal 6
Special notes 6
Foreword 7
A&D Technical support 8
Online Service and support 8
Europe/Africa (Erlangen) 8
America (Johnson City) 8
Asia/Pacific (Beijing) 8
Contact address 9
Regional contacts 9
Table of contents 11
Table of contents 13
Safety information 17
Transport and storage 19
Repairs 19
2.1 The frequency converter 21
Commissioning functions 22
Interfaces 23
Operating functions 23
Function modules 23
Protective functions 23
    24
Description 29
2.4 Overview of the LEDs 30
   33
3.1.1 Optical interface 34
3.2 PTC/KTY84 interface 35
Installation 37
4.2 Mounting the racks 38
Tools required 39
Accessories required 40
Required Tools 41
Procedure 41
4.4 Mounting the bus module 43
Required tools 44
Installation 45
Motor cable 53
Power transmission 53
Procedure: 54
Figure 5-1 Master system 60
Figure 5-4 Configuration 61
Address/ID 62
Parameter 63
Figure 5-8 Parameter 64
Specifying the device name 67
Figure 5-15 Configuration 68
Figure 5-19 Parameter 71
Parameter description 75
Commissioning (hardware) 77
6.1 Startup of ET 200pro 78
IEC motor 80
NEMA motor 80
Entering the type plate data 81
7.1 Commissioning sequence 83
7.1 Commissioning sequence 84
7.2.1 General 85
STARTER projects 86
Parameter settings 90
General settings 91
Temperature encoder 92
JOG frequency 93
Additional setpoints 93
6NLSIUHTXHQF\ 94
Fieldbus parameter 96
Process data monitoring 97
P2040 telegram failure time 97
Control word 1 (STW1) 98
Status word 1 (ZSW1) 100
7.4.2.2 Examples 101
ET 200pro FC 102
7.4.3.1 Block call 103
7.4.3.2 Examples 109
General steps 115
Description 117
Acceptance test 117
Checksums 117
Functional test 118
Completing the report 118
Appendix 118
Overview 119
7.6.1 Factory settings 120
Required parameter settings 121
Requirements 123
Internal memory 124
External memory 124
Download 125
Supplementary conditions 125
Manual download 127
Automatic download 128
See also 130
Fault codes 131
Remedy for F00395 131
8.2.1 Application ID 133
8.2.2 Series commissioning 134
Frequency converter with MMC 136
Normal startup without MMC 137
Normal startup with MMC 137
Interrupts 139
Resetting fault codes 139
Status display through LEDs 140
Description of the LEDs 141
Standard functions 141
9.2 Diagnostics through LEDs 142
Prerequisites 144
Evaluating 144
9.5 Device diagnostics 145
9.6 Fault clearance 145
10.1 Technical data 147
Ambient conditions 148
Shocks and vibrations 149
Air pollution/water 149
Installation and cooling 149
11.1 Frequency converter 151
11.2 Bus module 152
Spare parts/accessories 153
Power jumper connector 154
Sealing cap for power bus 154
A.1 Acceptance Log 155
A.1 Acceptance Log 156
Executing the test 157
Appendix 159
A.1 Acceptance Log 159
Data back-up/archiving 162
Signatures 162
A.2 ESD directives 163
Environment 1 164
Environment 2 164
Class C1 164
Class C2 164
EMC emitted interference 165
Harmonic currents 165
EMC immunity 166
A.2 ESD directives 167
A.2 ESD directives 168
A.3 Standards 170
B.1 Abbreviations 171
B.1 Abbreviations 172
B.1 Abbreviations 173
Glossary 181
Load groups 182
Monitoring cycle 182
Monitoring parameters 182
Parameter attributes 182
Changeable in 183
Data types 183
Quick commissioning 184
Range of values 185
Data sets 185
Potential groups 185
Switch-off signal paths 185
Upload and download 186
Writable parameters 186

Komentáře k této Příručce

Žádné komentáře

Siemens ET 757 E Series Provozní pokyny Strana 61

Komentáře k této Příručce

Související produkty a manuály pro Sporáky Siemens ET 757 E Series