Siemens IC60 Uživatelský manuál Strana 110
- Strana / 172
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Zones
110
Building Technologies
Fire Safety & Security Products
Option Display text Description
-
Up to version 9.07: Spare
3
No Exit Delay
Valid as of version 9.07:
Zone is not an Exit Delay Zone: if this option is turned on the zone will not have any
exit delay and will cause an instant alarm if triggered during the exit delay time. Also
you MUST ensure that if this option is turned on for a zone, that same zone should
not have any entry delay (P144E) programmed. If the zone does have an entry delay
the zone can activate during the exit time thereby starting an entry delay on the same
zone which means the user might not be aware of the pending alarm and leave the
premises. If the zone has no entry delay and the zone is triggered during the exit time
the alarm will then be instant alerting the user that they deviated off the exit route.
According EN 50131-3 the user must have an option to define the zones in the exit
route.
4
Prox Reader
Input
Keypad Zone: if this option is on the Zone will follow the Input at the corresponding
Proximity Reader. If the Proximity Reader is set to Keypad # 1 the input will be either
zone 1 or zone 9, e.g. if P122E 1E (zone #1) had option 4 on then the input at reader
one will operate zone 1. If P122E 9E (zone #9) had option 4 on then the input at
reader one will operate zone 9. Proximity reader 1 can operate zones 1 or 9 through
to proximity reader 8 can operate zones 8 or 16.
5
Radio Device
Zone is a Radio Zone: if this option is on the panel does not scan the hardwired zone
input terminal but instead is looking for a radio zone signal. The correct radio type
should be set at location P127E to ensure that the radio zone works correctly.
6
Stay Mode
Zone is a Stay Mode Zone: if this option is on the zone will be active when Stay Mode
is armed. This feature is normally used for arming just part of the alarm at night time.
7
Bypass able
Zone can be Manually Bypassed: if this option is on the zone can be Manually
Bypassed at the keypad using the
button. A zone must be Bypassed while in the
disarmed state. A bypassed zone will also bypass any tampers associated with that
zone. Once the area with the bypassed zone has been armed then disarmed, the
manual bypass is removed and the zone must be manually bypassed again before
arming if required. If a zone is configured as a 24 Hour zone (P123E Options 3,4 & 5),
they can also Manually Bypassed but in this case the Bypass must be manually
removed to re-instate the zone
8
Auto Bypass able
Zone can be Auto-Bypassed: if this option is on the zone will be Auto-Bypassed if
unsealed at the expiry of the exit delay. If a zone is unsealed at the time of arming
and remains unsealed when the exit delay expires and this option is on for that zone it
will be automatically bypassed by the panel. If the zone seals after that time it will be
re-instated automatically and can then cause an alarm. On disarming of the alarm any
auto-Bypasses are removed
- Wireless and hardwired 1
- IC60 - Sintony 60 1
- Installer Manual 1
- Building Technologies 10
- 1 Terminology 12
- 2.1 New features 13
- 2.2 Changes 13
- 3 Programming to EN 50131 15
- 4 System overview 18
- 4.2 Sintony 60 compact 20
- Z1Z10V 0V12V 12VCCC 21
- CCZ5Z2 Z6Z3 Z7Z4 Z8 TAMP 21
- 4.3 Zone connections 25
- 4.3.2 Zone wiring examples 26
- PIR Internal Connections 27
- 4.4 Inputs hardwired 28
- 4.5 Outputs hardwired 28
- 4.7 Programming port 29
- 5.2 Panic functions 30
- 6 Voice board IAV6-90 33
- 6.2.1 Pre-configuration 34
- 6.2.2 Recording messages 36
- 6.2.3 Playing messages 36
- 6.2.4 Re-recording messages 36
- 6.3 Operating instructions 37
- 6.3.1.2 Auto answering 38
- 6.3.3.1 Output DTMF 39
- 6.3.2.2 Call-back 39
- 6.4 Mute siren 41
- 7.3 Radio receiver IRFW6 42
- 8 LCD keypad 43
- Sequence Action 47
- Language 48
- Keypad Number 1 49
- 8.6 Operating a LCD keypad 53
- 8.6.4 LCD quick view mode 54
- 8.6.7 Send manual test call 55
- Program ( 61
- ) Button 61
- 10 Default access codes 62
- 11 Programming users 63
- 11.2 User code type 64
- 11.3 User access options 65
- 11.4 User code privileges 66
- 11.5 Radio user type 67
- 11.6 Radio user privileges 67
- 11.10 User to output mask 70
- 13.1 Installer code 75
- 13.2 Duress digit 75
- 13.3 Dial report delay 75
- 13.5 Two trigger timer 76
- Miscellaneous Options 78
- P25E 10E1-8E 78
- Installer Options 79
- P25E 11E 1-8E 79
- Miscellaneous User Options 80
- P25E 13E 1-8E 80
- 15 Time and date setting 82
- 16 Outputs 84
- Outputs 85
- Output B Options 85
- P35E 1-8E 1-8E 85
- Output C Options 85
- P36E 1-8E 1-5E 85
- 16.4 Un-map an output 87
- 17 Areas 89
- Area B Options 90
- P46E 1-2E 1-8E 90
- (1 = Area A, 2 = Area B) 90
- 18 Keypads 97
- Keypad ARM Areas 99
- P74E 1-8E 1-2E 99
- Keypad ARM Access 99
- P75E 1-8E 1-8E 99
- Keypads 100
- Keypad STAY Areas 100
- P76E 1-8E 1-2E 100
- Keypad STAY Access 100
- P77E 1-8E 1-8E 100
- Keypad A Key Areas 101
- P78E 1-8E 1-2E 101
- Keypad A Key Options 101
- P79E 1-8E 1-8E 101
- Keypad B Key Areas 102
- P80E 1-8E 1-2E 102
- Keypad B Key Options 102
- P81E 1-8E 1-8E 102
- 18.8 Keypad to output mask 103
- 18.12 Keypad chime timer 105
- 19 Key-switches 107
- Key-switches 108
- Keyswitch Access 108
- P112E 1-2E 1-8E 108
- 20 Zones 109
- Zone B Options 111
- P123E 1-16E 1-8E 111
- Zone C Options 112
- P124E 1-16E 1-8E 112
- 20.9 Zone timing settings 118
- 20.9.2 Retrigger time 119
- 21 Time zones 121
- 22 Dialer 123
- Dialer B Option 124
- P175E 2E 1-8E 124
- 22.2 Auto answer ring count 125
- 22.3 Test call options 125
- 22.5 Dialing pre-fix numbers 127
- 23 Telephone numbers 129
- Telephone numbers 130
- Phone Options 131
- P183E 1-8E 1-8E 131
- 23.5 Dial progress options 132
- Phone B Reporting 133
- P187E 1-8E 1-8E 133
- Phone C Reporting 133
- P188E 1-8E 1-8E 133
- Phone D Reporting 134
- P189E 1-8E 1-8E 134
- Divert Options 136
- P193E 1-2E 1-8E 136
- 24 4 plus 2 program options 137
- 4 plus 2 program options 138
- 26 Contact ID code summary 141
- 27.5 Reset back to defaults 146
- 27.6 Start a call-back call 147
- 27.7 Installer code 147
- 28 User privileges chart 148
- User privileges chart 149
- 30.1 Installer menu 151
- 30.2 Installer: Users 152
- 30.3 Clock settings 153
- 30.4 Phone numbers 154
- 30.5 Dialer 155
- 30.6 Areas 156
- 30.7 Zones main 157
- 30.8 Zones outputs 158
- 30.9 Keypads 159
- 30.10 Outputs 160
- 30.11 Keyswitch 161
- 30.12 Miscellaneous 162
- 30.13 4+2 event codes 163
- 30.14 SIA event codes 164
- 30.15 Diagnostics 165
- 31 Support 166
- Support 171
- After a voice alarm ...: 171
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens IC60
(50 stránky)
(184 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.140 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce