Siemens Pacemaker UM344-2 Uživatelský manuál Strana 82
- Strana / 183
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
ON-LINE AND OFF-LINE OPERATION UM344-2
September 1995
5
-
12
1. Choose END at the Function Block Menu in configuration
mode to display the Configuration Complete Menu. It shows
these selections: QUIT, SAVE, REVIEW, or
DOWNLOAD. Choose one after all configuration changes
are entered.
QUIT - return to the MXC's On-Line Menu (adjacent) that
appeared after initial communication had been established.
SAVE - go to the Save To Archive screen to save the
transmitter configuration in an archive. The MXC will show
the tagname, the archive location last used in the MXC, and
three selections: YES, NEW ARCH, and END.
YES - save the configuration in the archive location
shown on the screen. If the archive shown contains a
configuration (other than a default configuration), a
Caution screen will be displayed. Press Enter to
overwrite the stored configuration.
NEW ARCH - save the configuration to a new archive
location.
END - return to the previous screen without saving.
REVIEW - return to the Function Block Menu. The
configuration can be reentered and edited from this Menu by
pressing CONT.
DOWNLOAD - downloads the configuration to the
transmitter. Go to the next section.
5.1.2 Downloading A
Configuration
After all configuration information has been edited at the MXC,
download the configuration to the transmitter. A download can
be performed in configuration mode at any time by pressing a
series of END and SEL/END keys until a DOWNLOAD key is
visible on the screen.
1. Press DOWNLOAD to send the configuration to the
transmitter.
Ÿ If no changes have been made to a configuration and
DOWNLOAD is pressed, the MXC will display the
adjacent screen and will not perform a download to
prevent unnecessary communication.
CONFIGURATION
COMPLETE
RE- DOWN
QUIT SAVE VIEW LOAD
Dev ID: 210300003C
Tag: TTC-101 ADD: 00
LOOP CAL/ CON -
END
OVRD
TEST FIG
SAVE TO ARCHIVE 92
TTC-101
NEW
YES ARCH END
CAUTION - PRESSING
ENTER WILL REPLACE
ARCH 00 A- EN-
PTC - 101 BORT TER
TEMP XMTR
MODEL 344
TYPE 03
QUIT CONT
NO CONFIGURATION
CHANGES MADE.
DOWNLOAD ABORTED.
CONT
WARNING! DOWNLOADING
WILL CHANGE XMTR
CONFIG- A- DOWN
URATION BORT LOAD
- USER’S MANUAL 1
- TABLE OF CONTENTS 2
- CONTENTS UM344-2 3
- September 1995 3
- UM344-2 CONTENTS 4
- September 1995 4
- SECTION AND TITLE PAGE 5
- LIST OF ILLUSTRATIONS 6
- LIST OF TABLES 7
- 1.0 INTRODUCTION 10
- FIGURE 1-1 Basic Model 344 11
- X02869S1 12
- 2.0 XTC COMMUNICATOR 14
- MOORE XTC COMMUNICATOR 15
- SELECT BLOCK TO EDIT 16
- - SENSOR INPUT 16
- PREV NEXT END ECT 16
- SELECT FUNCTION 18
- FIND ARCH TEST 18
- XMTR FUNC MXC END 18
- X02849S1 19
- LOOP OVERRIDE - CHOOSE 21
- CURRENT OUTPUT LEVEL 21
- 4 MA 20 MA OTHR END 21
- X02807S1 25
- SHORT OR LONG FORM 27
- ADDRESS? 27
- SHRT LONG 27
- ADDR ADDR POLL END 27
- MXC SELF TEST 28
- TEST TEST 28
- KEYS SCRN END 28
- WARNING! SELF TEST 30
- MAY BUMP TRANSMITTER 30
- OUTPUT A 30
- 4.0 INSTALLATION 35
- X02866S1 39
- X02867S1 40
- X02868S1 41
- X02817S1 42
- X02821S1 52
- Wall Mounting 53
- X02818S0 57
- FIGURE 4-8 Sensor Assembly 58
- X028AAS0 60
- X02870S1 61
- X02824S1 63
- TESTSIGNAL 66
- X02825S1 67
- MV LO : 0.0000 74
- ENTER MV LO: 74
- (F4) to change the setpoint 78
- DOWNLOADING 84
- CONFIGURATION 84
- - PLEASE WAIT 84
- DOWNLOAD 84
- COMPLETE 84
- MANUAL control mode to 92
- MANUAL control mode 92
- DG MR END CONT 96
- WARNING : ARCHIVE 97
- CONTAINS NO DATA 97
- A 97
- ERROR! ARCHIVE TYPE 98
- DOESN'T MATCH THE 98
- TRANSMITTER TYPE 98
- X02808S1 106
- X02827S1 1 of 2 111
- X02827S1 2 of 2 112
- APPLY 103.00 mV TO 115
- WITH COPPER WIRE 115
- CAL TEST END 118
- CALIBRATE / TEST 118
- TRANSMITTER PASSED 121
- TRANSMITTER SELFTEST 121
- 7.0 CIRCUIT DESCRIPTION 134
- Output Circuitry 135
- Input Circuitry 135
- X02815S0 142
- Z FS 146
- 9.0 GLOSSARY 154
- 4 - 20 mA 160
- Failsafe Level 160
- Absolute Alarm #1 161
- Absolute Alarm #2 161
- R = 162
- X02879S0 163
- Block Diagram, PD Controller 164
- Block Diagram, ID Controller 165
- X02881S1 168
- WARRANTY 177
- WARRANTY UM344-2 178
- W-2 October 1996 178
- PARTS LIST 179
- USER’S MANUAL ADDENDUM 181
- X03013S1 182
Související produkty a manuály pro Měření, testování a kontrola Siemens Pacemaker UM344-2
(22 stránky)
(22 stránky)
Měření, testování a kontrola Siemens BTC-BR Manuál
(264 stránky)
(264 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce