Siemens Pacemaker UM344-2 Uživatelský manuál Strana 98
- Strana / 183
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
ON-LINE AND OFF-LINE OPERATION UM344-2
September 1995
5
-
28
4. Use PREV and NEXT to select the transmitter type -
Temperature - then press SELECT. The default configur-
ation for a temperature transmitter will be loaded into the
Off-Line Memory of the MXC.
5. The next screen shows the archive number to be edited.
Press either EDIT ARCH to begin editing or END to select
another archive number.
6. Press CONT to continue and select a configuration block for
editing. Refer to Section 5.1.1 to edit configuration
parameters.
Press QUIT to return to the previous screen.
After configuration is complete:
1. Press END in the Function Block menu to access the
following three choices from the adjacent screen.
QUIT - go to the Main Menu and end configuration.
REVIEW - return to the Function Block menu to make any
changes or additions. Refer to Section 5.1.1 as necessary.
SAVE - show the archive number and tagname of the
current configuration and provide the option to save the
configuration either under the current archive number or
under a new number. Go to step 2.
2. Press YES in the Save Archive screen to save the archive
under the current number. Perform one of the two steps
below:
Ÿ If the new configuration will overwrite an existing
archive, the MXC will provide a warning message before
the store operation is performed. Press ENTER to
continue.
Ÿ If the tagname of a new configuration has already been
assigned to an archived configuration, a WARNING
screen appears. Press CONT to move to the TRANS-
MITTER ID block and display the tag selection.
- If the tagname is not to be changed, press either
SEL/END to return to the Save Archive screen or
SEL/CONT to return to the previous screen.
SELECT X-MITTER TYPE
TEMP CONTROLLER
PREV
NEXT
END
SEL-
ECT
ARCHIVE 97 DEFAULT
SELECT A FUNCTION
EDIT
ARCH END
CONFIGURATION
COMPLETE
RE-
QUIT SAVE VIEW
SAVE TO ARCHIVE 97
DEFAULT
NEW
YES ARCH END
ERROR! ARCHIVE TYPE
DOESN'T MATCH THE
TRANSMITTER TYPE
CONT
WARNING: TAG NAME
USED ENTER NEW TAG
NAME.
CONT
- USER’S MANUAL 1
- TABLE OF CONTENTS 2
- CONTENTS UM344-2 3
- September 1995 3
- UM344-2 CONTENTS 4
- September 1995 4
- SECTION AND TITLE PAGE 5
- LIST OF ILLUSTRATIONS 6
- LIST OF TABLES 7
- 1.0 INTRODUCTION 10
- FIGURE 1-1 Basic Model 344 11
- X02869S1 12
- 2.0 XTC COMMUNICATOR 14
- MOORE XTC COMMUNICATOR 15
- SELECT BLOCK TO EDIT 16
- - SENSOR INPUT 16
- PREV NEXT END ECT 16
- SELECT FUNCTION 18
- FIND ARCH TEST 18
- XMTR FUNC MXC END 18
- X02849S1 19
- LOOP OVERRIDE - CHOOSE 21
- CURRENT OUTPUT LEVEL 21
- 4 MA 20 MA OTHR END 21
- X02807S1 25
- SHORT OR LONG FORM 27
- ADDRESS? 27
- SHRT LONG 27
- ADDR ADDR POLL END 27
- MXC SELF TEST 28
- TEST TEST 28
- KEYS SCRN END 28
- WARNING! SELF TEST 30
- MAY BUMP TRANSMITTER 30
- OUTPUT A 30
- 4.0 INSTALLATION 35
- X02866S1 39
- X02867S1 40
- X02868S1 41
- X02817S1 42
- X02821S1 52
- Wall Mounting 53
- X02818S0 57
- FIGURE 4-8 Sensor Assembly 58
- X028AAS0 60
- X02870S1 61
- X02824S1 63
- TESTSIGNAL 66
- X02825S1 67
- MV LO : 0.0000 74
- ENTER MV LO: 74
- (F4) to change the setpoint 78
- DOWNLOADING 84
- CONFIGURATION 84
- - PLEASE WAIT 84
- DOWNLOAD 84
- COMPLETE 84
- MANUAL control mode to 92
- MANUAL control mode 92
- DG MR END CONT 96
- WARNING : ARCHIVE 97
- CONTAINS NO DATA 97
- A 97
- ERROR! ARCHIVE TYPE 98
- DOESN'T MATCH THE 98
- TRANSMITTER TYPE 98
- X02808S1 106
- X02827S1 1 of 2 111
- X02827S1 2 of 2 112
- APPLY 103.00 mV TO 115
- WITH COPPER WIRE 115
- CAL TEST END 118
- CALIBRATE / TEST 118
- TRANSMITTER PASSED 121
- TRANSMITTER SELFTEST 121
- 7.0 CIRCUIT DESCRIPTION 134
- Output Circuitry 135
- Input Circuitry 135
- X02815S0 142
- Z FS 146
- 9.0 GLOSSARY 154
- 4 - 20 mA 160
- Failsafe Level 160
- Absolute Alarm #1 161
- Absolute Alarm #2 161
- R = 162
- X02879S0 163
- Block Diagram, PD Controller 164
- Block Diagram, ID Controller 165
- X02881S1 168
- WARRANTY 177
- WARRANTY UM344-2 178
- W-2 October 1996 178
- PARTS LIST 179
- USER’S MANUAL ADDENDUM 181
- X03013S1 182
Související produkty a manuály pro Měření, testování a kontrola Siemens Pacemaker UM344-2
(22 stránky)
(22 stránky)
Měření, testování a kontrola Siemens BTC-BR Manuál
(264 stránky)
(264 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce