Siemens SIPART PS2 6DR50xx Provozní pokyny Strana 174
- Strana / 242
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Alarm, error, and system messages
11.1 Representation of system messages in the digital display
SIPART PS2 with and without HART communications
174 Operating Instructions, 09/2007, A5E00074631-07
11.1.2 System messages during initialization
Remarks about the tables:
nn stands for variable numeric values
Error symbol
/ (Slash): texts to the left and the right of the slash blink alternately
Messages during initialization
Line Message
Up Down
Meaning / cause Measure
P-- X Measuring range was exceeded, the
potentiometer is in the inactive zone, the
transmission ratio selectors or the effective
lever arm are not adjusted as per the
actuator travel
• Switch the transmission ratio selector to
90° especially in case of part-turn
actuators
• Adjust the effective lever length of linear
actuators as per the measuring range
RUN1 X Initialization was started, part 1 is active (the
direction of action is determined)
• Wait
RUN2 X Initialization part 2 is active (actuator travel
check and determination of end stops)
• Wait
RUN3 X Initialization part 3 is active (determination
and display of actuating times)
• Wait
RUN4 X Initialization part 4 is active (determination of
the minimum controller increment length)
• Wait
RUN5 X Initialization part 5 is active (optimization of
the transient response)
• Wait until "FINSH" is displayed
(initialization completed successfully)
• Acknowledge by pressing the operating
mode button slightly and exit the
configuration level by pressing it longer
YEND1 X The first end position can be approached
only in case of a manual initialization
• Approach the first end position using the
"+" or "-" button
• Acknowledge using the operating mode
button
YEND2 X The second end position can be approached
only in case of a manual initialization
• Approach the second end position using
the "+" or "-" button
• Acknowledge using the operating mode
button
RANGE X The end position or the measuring span is
beyond the permissible range only in case of
a manual initialization
• Approach another end position using the
"+" and "-" buttons and acknowledge with
the operating mode button, or
• Move the friction clutch until "ok" is
displayed, and then acknowledge with
the operating mode button, or
• Terminate the initialization process by
pressing the operating mode button,
switch to the P-manual mode and correct
the actuator travel and the position
displacement sensor
- sipart 1
- Electropneumatic positioners 3
- SIPART PS2 with and without 3
- HART communications 3
- Table of contents 5
- Table of contents 7
- Introduction 11
- 1.3 Further information 12
- General safety notes 13
- 2.4 Measures 14
- 2.5 Qualified Personnel 15
- 2.6 SIL applications 15
- 3.2 Structure 18
- Description 19
- 3.2 Structure 19
- Functional principle 21
- 3.4 Device components 23
- 3.4.2 Motherboard 24
- 3.4.4 Pneumatic connections 25
- Structure 26
- 3.4 Device components 27
- 3.4.5 Purge air switching 28
- 3.4.6 Restrictors 28
- 3.5 Mode of operation 29
- 3.5.2 Control algorithm 30
- 3.5 Mode of operation 31
- Function 32
- Mounting 33
- Installing the positioner 35
- Mounting 37
- 40
- 0% 20 40 60 80 100% 41
- Procedure 45
- Installing option modules 49
- Installing option modules 51
- Installing the module cover 54
- 5.2 Iy module 55
- 5.3 Alarm unit 56
- 5.4.1 SIA unit 58
- Installing the SIA unit 59
- Setting the L1 and L2 limits 60
- Device features 61
- 5.6 EMC filter module 63
- 5.7 Accessories 65
- Warning labels 66
- Connection 67
- 6.1 Electrical connection 68
- Two-wire mode 69
- 6.1.2.1 Basic device 70
- 6.1.2.2 Current output 71
- 6.1.2.4 SIA unit 72
- Connection 73
- 6.1 Electrical connection 73
- 6.1.3.1 Basic device 77
- Basic device 77
- 6.1.3.2 Split range 79
- 6.1.3.3 Current output 80
- 6.1.3.5 SIA unit 82
- 6.1.4.1 Basic device 85
- 6.1.4.2 Current output 87
- 6.1.4.4 SIA unit 88
- 6.2 Pneumatic connection 89
- Operating 91
- 7.1.2 Buttons 93
- 7.2 Operating modes 94
- VLPXOWDQHRXV VLPXOWDQHRXV 96
- Manual mode (MAN) 97
- Automatic (AUT) 97
- Diagnostics 97
- Operating 99
- 8.1 General safety notes 101
- Description 102
- Functional safety 103
- 8.2.2 Safety function 104
- 8.2.3 Settings 105
- Checking the safety function 106
- Repairs 106
- See also 106
- Commissioning 107
- Sequence of RUN1 109
- Commissioning 111
- IODVKHV 113
- DOWHUQDWLQJ 113
- Condition 114
- Connecting the positioner 114
- Setting the actuator 115
- Conditions 115
- Setting parameter 3 117
- Replacing the positioner 126
- Parameterizing/addressing 129
- 10.3 Overview of parameters 131
- Overview 132
- Parameterizing/addressing 133
- 10.3 Overview of parameters 134
- Overview parameter A 135
- Overview parameter b 136
- Overview parameter C 136
- Overview parameter d 136
- Overview parameter E 136
- Overview parameter F 136
- Overview parameter G 137
- Overview parameter H 137
- Overview parameter J 137
- Overview parameter L 137
- Overview parameter O 138
- Overview parameter P 138
- 1.YFCT - actuator type 138
- 8.SPRE - Split range start 142
- 9.SPRE - Split range end 142
- 10.TSUP - Setpoint ramp OPEN 143
- 12.SFCT - Setpoint function 143
- 44.AFCT - Alarm function 149
- 50.PRST - Preset 152
- PST - partial stroke test 153
- A1.STPOS - start position 154
- A2.STTOL - start tolerance 154
- A3.STEP - step height 154
- A4.STEPD - step direction 154
- A5.INTRV - test interval 155
- A7.FACT1 - factor 1 155
- A8.FACT2 - factor 2 155
- A9.FACT3 - factor 3 156
- LEAK - pneumatic leakages 158
- C2.FACT1 - factor 1 159
- C3.FACT2 - factor 2 159
- C4.FACT3 - factor 3 159
- DEBA - dead zone monitoring 161
- F1.LEVL1 - threshold 1 162
- F2.LEVL2 - threshold 2 162
- F3.LEVL3 - threshold 3 163
- G1.LEVL1 - threshold 1 164
- G2.LEVL2 - threshold 2 164
- G3.LEVL3 - threshold 3 164
- J3.LEVL2 - threshold 2 167
- J4.LEVL3 - threshold 3 167
- L2.FACT1 - factor 1 168
- L3.FACT2 - factor 2 168
- L4.FACT3 - factor 3 168
- P3.LEVL1 - threshold 1 171
- P4.LEVL2 - threshold 2 171
- P5.LEVL3 - threshold 3 171
- Messages during operation: 177
- 11.2 Diagnosis 178
- Explanation about the table 179
- Diagnostic value 53 180
- 11.2 Diagnosis 181
- 10 LEAK - leakage 182
- 11.2 Diagnosis 184
- 44 PRDN - prediction down 186
- 11.3 Online diagnostics 187
- 11.3.2 XDIAG parameter 188
- 11.3 Online diagnostics 190
- 11 Pneumatic leakage 191
- 13 Temperature undershot 192
- 14 Temperature overshot 192
- 11.4 Fault correction 193
- Service and maintenance 199
- Dismantling 200
- Installation 200
- Technical data 201
- 13.1 General technical data 202
- Technical data 203
- SIPART PS2 HART 204
- Optional modules 206
- Dimension drawings 211
- Dimension drawings 213
- 15.1 Overview 215
- Options 216
- Accessories 216
- 15.3 Optional modules 217
- 15.4 Spare parts 218
- 15.4 Spare parts 219
- Small part set 1 220
- Small part set 2 221
- 15.6 Accessories 222
- Appendix 223
- SIEMENS AG, A&D PI TQ2 225
- A.3 Test report (extract) 226
- Appendix 227
- A.3 Test report (extract) 227
- Abbreviations 229
- Glossary 231
- Glossary 233
- Zone 22 238
- Index 241
- A5E00074631 242
Související produkty a manuály pro Příslušenství a součásti motorových vozidel Siemens SIPART PS2 6DR50xx
(22 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce