Siemens SINUMERIK 802D sl Návod k obsluze stáhnout pdf (Strana 176)

Overview of alarms 06/2009

NCK alarms

2-176

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

22322 [Channel %1: ] Axis %2 PRESET: illegal value

Parameters: %1 = Channel number

%2 = Axis name, spindle number

Definitions: The entered Preset value is too large (number format overflow).

Reaction: NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Use more realistic (smaller) Preset values.

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

25000 Axis %1 hardware fault of active encoder

Parameters: %1 = Axis name, spindle number

Definitions: The signals of the currently active position actual value encoder (NC/PLC interface signal V380x

0001.5 = 1 (Position measuring system 1) or V380x 0001.6 = 1 (Position measuring system 2)) are

missing, do not have the same phase, or exhibit grounding/short-circuit.

The alarm can be reprogrammed in the MD11412 $MN_ALARM_REACTION_CHAN_NOREADY

(channel not ready).

For PROFIdrive only:

MD36310 $MA_ENC_ZERO_MONITORING >100 replaces the existing PowerOn alarm by the Reset

alarm 25010.

Reaction: Mode group not ready.

The NC switches to follow-up mode.

Channel not ready.

NC Start disable in this channel.

Axes of this channel must be re-referenced.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Channel not ready.

Remedy: Please inform the authorized personnel/service department. Check measuring circuit connectors for

correct contacting. Check encoder signals and replace the encoder if faults are found.

Monitoring can be switched off by setting MD36310 $MA_ENC_ZERO_MONITORING[n] to 100 (n =

encoder number: 1,2).

Program Con-

tinuation:

Switch control OFF - ON.

25001 Axis %1 hardware fault of passive encoder

Parameters: %1 = Axis name, spindle number

Definitions: The signals from the currently inactive position actual value encoder are missing, or they are not of

the same phase, or they exhibit grounding/short-circuit.

For PROFIdrive only:

MD36310 $MA_ENC_ZERO_MONITORING >100 replaces the existing PowerOn alarm by the Reset

alarm 25011.

MD36310 $MA_ENC_ZERO_MONITORING >100 replaces the existing Reset alarm by the Cancel

alarm 25011.

Reaction: Alarm display.

Remedy: Please inform the authorized personnel/service department. Check measuring circuit connectors for

correct contacting. Check encoder signals and replace the encoder if faults are found. Switch off mon-

itoring with the corresponding interface signal V380x 0001.5 / 1.6 = 0 (Position measuring system 1/2

Monitoring can be switched off by setting MD36310 $MA_ENC_ZERO_MONITORING[n] to 100 (n =

encoder number: 1,2).

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

25010 Axis %1 pollution of measuring system

Parameters: %1 = Axis name, spindle number

Definitions: The encoder used for position control sends a contamination signal (only in measuring systems with

contamination signal).

1 2 ... 171 172 173 174 175 176 177 178 179 180 181 ... 339 340

Komentáře k této Příručce

Žádné komentáře

Siemens SINUMERIK 802D sl Návod k obsluze Strana 176

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens SINUMERIK 802D sl