Siemens SINUMERIK 802D sl Návod k obsluze stáhnout pdf (Strana 23)

NCK alarms

06/2009 Overview of alarms

2-23

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

4152 Illegal configuration of the 'Block display with absolute values' function

Definitions: The "Block display with absolute values" function has been illegally parameterized:

- An illegal block length has been set with MD28400 $MC_MM_ABSBLOCK:

While ramping up, the machine data will be checked for the following value range:

0, 1, 128 to 512

- An invalid display range has been set with MD28402 $MC_MM_ABSBLOCK_BUFFER_CONF[].

While ramping up, the machine data will be checked for the following upper and lower limits:

0 <= MD28402 $MC_MM_ABSBLOCK_BUFFER_CONF[0] <= 8

0 <= MD28402 $MC_MM_ABSBLOCK_BUFFER_CONF[1] <= (MD28060

$MC_MM_IPO_BUFFER_SIZE + MD28070$MC_MM_NUM_BLOCKS_IN_PREP).

Alarm 4152 is issued if the limits are violated.

Reaction: Mode group not ready.

Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Configure block length/display range within the permissible limits.

Program Con-

tinuation:

Switch control OFF - ON.

4160 [Channel %1: ] Invalid M function number configured for spindle

switchover

Parameters: %1 = Channel number

Definitions: An M function was specified in MD20094 $MC_SPIND_RIGID_TAPPING_M_NR in order to configure

the M function number for spindle switchover. The M function number is assigned by the system and

cannot be used for the switchover (M1 to M5, M17, M30, M40 to M45).

Reaction: Mode group not ready.

Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Configure an M function which is not used by the system (M1 to M5, M17, M30, M40 to M45) in

MD20094 $MC_SPIND_RIGID_TAPPING_M_NR.

Program Con-

tinuation:

Switch control OFF - ON.

4181 [Channel %1: ] Invalid assignment of an M auxiliary function number

Parameters: %1 = Channel number

Definitions: In MD22254 $MC_AUXFU_ASSOC_M0_VALUE or MD22256 $MC_AUXFU_ASSOC_M1_VALUE, a

number has been specified for the configuration of a new predefined M function which is occupied by

the system, and cannot be used for an assignment. (M0 to M5, M17, M30, M40 to M45).

Reaction: Mode group not ready.

Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Configure an M function in machine data MD22254 $MC_AUXFU_ASSOC_M0_VALUE or MD22256

$MC_AUXFU_ASSOC_M1_VALUE which is not occupied by the system (M1 to M5, M17, M30, M40

to M45).

Program Con-

tinuation:

Switch control OFF - ON.

4182 [Channel %1: ] Invalid M auxiliary function number in %2%3, MD reset

Parameters: %1 = Channel number

%2 = MD identifier

%3 = If required, MD index

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 339 340

Komentáře k této Příručce

Žádné komentáře

Siemens SINUMERIK 802D sl Návod k obsluze Strana 23

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens SINUMERIK 802D sl