Siemens SINUMERIK 802D sl Návod k obsluze stáhnout pdf (Strana 286)

Overview of alarms 06/2009

PROFIBUS alarms

2-286

SINUMERIK 802D sl, Diagnostics Manual, 06/2009

Remedy: Enter correct base addresses in the machine data:

- For length=1: Correct machine data MN_HW_ASSIGN_DIG_FASTIN.

- For length=2: Correct machine data MN_HW_ASSIGN_ANA_FASTIN.

- NCK restart

If the error cannot be eliminated by this procedure, please make a note of the error text and contact

the control system manufacturer.

Program Con-

tinuation:

Switch control OFF - ON.

380071 PROFIBUS/PROFINET: No output slot available for basic address %1

(size %2)

Parameters: %1 = Logical base address of the requested area

%2 = Size of the area in bytes

Definitions: An incorrect logical base address was specified for a digital or analog input. Either no slot has been

configured for this base address or the requested area extends beyond the end of the slot.

For length =1 it is a digital output,

For length =2 it is an analog output.

Reaction: Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Enter correct base addresses in the machine data:

- For length=1: Correct machine data MN_HW_ASSIGN_DIG_FASTOUT.

- For length=2: Correct machine data MN_HW_ASSIGN_ANA_FASTOUT.

- NCK restart

If the error cannot be eliminated by this procedure, please make a note of the error text and contact

the control system manufacturer.

Program Con-

tinuation:

Switch control OFF - ON.

380072 PROFIBUS/PROFINET: Output slot for basic address %1 (size %2) not

allowed

Parameters: %1 = Logical base address of the requested area

%2 = Size of the area in bytes

Definitions: An incorrect logical base address was set for a digital or analog output, the area is resides in the

access range of the PLC (PIQ, base addresses < 256).

For length =1 it is a digital output,

For length =2 it is an analog output.

Reaction: Channel not ready.

NC Start disable in this channel.

Interface signals are set.

Alarm display.

Remedy: Only use addresses outside the PLC process image (e.g. >= 256) for output slots.

Enter correct basic addresses in the machine data:

- For length=1: Correct machine data MN_HW_ASSIGN_DIG_FASTOUT.

- For length=2: Correct machine data MN_HW_ASSIGN_ANA_FASTOUT.

- NCK restart

If the error cannot be eliminated by this procedure, please make a note of the error text and contact

the control system manufacturer.

Program Con-

tinuation:

Switch control OFF - ON.

380075 PROFIBUS/PROFINET: DP I/O failure bus %2 slave/device %1

Parameters: %1 = Slave/device address

%2 = Number of the affected bus

Definitions: Failure of a PROFIBUS/PROFINET slot used by the NCK for digital or analog I/Os.

Reaction: Alarm display.

Remedy: Check that the slave/device is operating correctly (all slaves/devices must be included in the bus,

green LEDs).

Program Con-

tinuation:

Alarm display showing cause of alarm disappears. No further operator action necessary.

1 2 ... 281 282 283 284 285 286 287 288 289 290 291 ... 339 340

Komentáře k této Příručce

Žádné komentáře

Siemens SINUMERIK 802D sl Návod k obsluze Strana 286

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens SINUMERIK 802D sl