Siemens SINUMERIK 802D sl Specifikace stáhnout pdf (Strana 195)

NCK alarms/ISO alarms

06/2007 Overview of alarms

2-195

SINUMERIK 802D sl, Diagnostics Manual, 06/2007Edition

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

16952 Channel %1 start program command not possible due to MDI

Parameters: %1 = channel ID

Definitions: The NCK is currently processing an ASUB in MDA mode. In this state, it is not legal to issue a "Start"

program command for another channel. Notice! If an asynchronous subprogram is started from JOG,

the NCK can switch internally to MDA if it was previously in this mode and has not been RESET. Note:

With-out this alarm, the MDA buffer of the other channel would always be started.

Reaction: NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Start asynchronous subroutine in AUTO or AUTO->JOG

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

16953 Channel %1 For slave axis %2 SERUPRO not allowed, as master axis %3

not subject to axis/spindle disable

Parameters: %1 = Channel number

%2 = Slave axis name, following spindle number

%3 = Master axis name, master spindle number

Definitions: Currently, the alarm occurs only in combination with the SERUPRO action. SERUPRO stands for

search via program test.

SERUPRO is possible only with an active coupling, if the axis/spindle disable is active for all master

axes/spindles of the slave axis/spindle

Reaction: NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: Set axis/spindle disable of the master axis

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

16954 Channel %1 block %2 programmed stop prohibited in stop delay area

Parameters: %1 = channel ID

%2 = block number, label

Definitions: A program command which causes a stop has been used in a program area (stop-delay area) which

is parenthesized by DELAYFSTON and DELAYFSTOF. Except for G4, no commands which cause

even a brief stop may be used in such areas. A stop-delay area can also be defined via MD 11550

STOP_MODE_MASK.

Reaction: Interpreter stop

NC Start disable in this channel.

Interface signals are set.

Alarm display.

NC Stop on alarm.

Remedy: MD 11550 STOP_MODE_MASK and NC command DELAYFSTON DELAYFSTOF

Program Con-

tinuation:

Clear alarm with the RESET key. Restart part program

16955 Channel %1 stop in stop delay area is delayed

Parameters: %1 = channel ID

Definitions: An event which causes a stop has been detected in a program area (stop-delay area) which is paren-

thesized by DELAYFSTON and DELAYFSTOF. The stop is delayed and executed after DELAYF-

STOF. A stop-delay area can also be defined via MD 11550 STOP_MODE_MASK.

Reaction: Interface signals are set.

Alarm display.

Remedy: MD 11550 STOP_MODE_MASK and NC command DELAYFSTON DELAYFSTOF

Program Con-

tinuation:

Alarm display showing cause of alarm disappears. No further operator action necessary.

1 2 ... 190 191 192 193 194 195 196 197 198 199 200 ... 391 392

Komentáře k této Příručce

Žádné komentáře

Siemens SINUMERIK 802D sl Specifikace Strana 195

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens SINUMERIK 802D sl