Siemens SINUMERIK 802D sl Specifikace stáhnout pdf (Strana 86)

Overview of alarms 06/2007

NCK alarms/ISO alarms

2-86

SINUMERIK 802D sl, Diagnostics Manual, 06/2007Edition

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12010 Channel %1 block %2 address %3 address type programmed too often

Parameters: %1 = channel number

%2 = block number, label

%3 = source string of address

Definitions: For each address type, it is defined internally how often it may occur in an NC block (for instance, all

axes together form one address type for which a block limit also applies).

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECTION. The correction pointer positions on the incorrect block.

The program information must be split up over several blocks (but make sure that the functions are of

the non-modal type!).

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12020 Channel %1 block %2 illegal address modification

Parameters: %1 = channel number

%2 = block number, label

Definitions: Valid address types are ‚IC‘, ‚AC‘, ‚DC‘, ‚ACN‘, ‚ACP‘. Not each of these address modifications can be

used for each address type. The Programming Guide specifies which of these can be used for the

various address types. If this address modification is applied to address types that are not allowed,

then the alarm is generated, e.g.:

N10 G02 X50 Y60 I=DC(20) J30 F100

; Interpolation parameters with DC.

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM COR-

RECT. The correction pointer positions on the incorrect block.

Apply non-modal address modifications only for permissible addresses, in accordance with the Pro-

gramming Guide.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

12040 Channel %1 block %2 expression %3 is not of data type 'AXIS'

Parameters: %1 = Channel number

%2 = Block number, label

%3 = Source string in the block

Definitions: Some vocabulary words require that the data in their parameters be written in variables of the type

"AXIS". For example, in the vocabulary word POS the axis identifier must be specified in the paren-

thesized expression, and it must be defined as a variable of the AXIS type. With the following vocab-

ulary words only parameters of the AXIS type are possible:

AX[..], FA[..], FD[..], FL[..], IP[..], OVRA[..], PO[..], POS[..], POSA[..]

Example:

N5 DEF INT ZUSTELL=Z1 incorrect, this does not specify an axis identifier but the number “26 161”

N5 DEF AXIS ZUSTELL=Z1 correct

N10 POS[ZUSTELL]=120 FA[ZUSTELL]=1000

Reaction: Correction block is reorganized.

Interface signals are set.

Alarm display.

Remedy: Key: Press the NC Stop key and select the function "Correction block" with the softkey PROGRAM

CORRECT. The correction pointer positions on the incorrect block.

Correct the part program in accordance with the instructions given in the Programming Guide.

Program Con-

tinuation:

Clear alarm with NC START or RESET key and continue the program.

1 2 ... 81 82 83 84 85 86 87 88 89 90 91 ... 391 392

Komentáře k této Příručce

Žádné komentáře

Siemens SINUMERIK 802D sl Specifikace Strana 86

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens SINUMERIK 802D sl