Siemens SINUMERIK 802D sl Specifikace stáhnout pdf (Strana 37)

NCK alarms/ISO alarms

06/2007 Overview of alarms

2-37

SINUMERIK 802D sl, Diagnostics Manual, 06/2007Edition

4503 In TO unit, %1 H number %2 assigned more than once. H number linked

again.

Parameters: %1 = TO unit

%2 = H number

Definitions: This error can only occur when MD $MN_MM_EXTERN_CNC_SYSTEM= 1 or 2. The Power ON

effective machine data bit 10890, $MN_EXTERN_TOOLPROG_MODE, bit 3 has been reset. On

reconstructing data handling after Power ON, it has been found that different edges of the same TO

unit have the same H number. They had been linked previously. They are linked again and MD bit

$MN_EXTERN_TOOLPROG_MODE, bit 3 is set again.

Reaction: Alarm display.

Remedy: H numbers must be assigned only once in a TO unit. Then, machine data bit 10890,

$MN_EXTERN_TOOLPROG_MODE, bit 3 can be set = 0 and a restart can be performed.

Program Con-

tinuation:

Clear alarm with the Delete key or NC START.

4610 Invalid handwheel module for handwheel %1

Parameters: %1 = Handwheel module

Definitions: The handwheel module for handwheel %1 requested through machine date

$MN_HANDWHEEL_MODULE is not available for 840D systems. An 840D system is always

regarded as a module. For this reason, handwheels directly linked with 840D systems

$MN_HANDWHEEL_MODULE = 1 must always be set.

Reaction: Interface signals are set.

Alarm display.

Remedy: Set machine date $MN_HANDWHEEL_MODULE = 1 for the corresponding handwheel.

Program Con-

tinuation:

Switch control OFF - ON.

4611 Invalid handwheel input for handwheel %1

Parameters: %1 = Handwheel input

Definitions: The handwheel input for handwheel %1 requested through machine date

$MN_HANDWHEEL_INPUT is not available for 840D systems. With 840D systems, a maximum of 3

handwheels can be linked directly (1st and 2nd directly to 840D HW, 3rd handwheel through free

encoder input).

Reaction: Interface signals are set.

Alarm display.

Remedy: Configure machine date $MN_HANDWHEEL_INPUT for a valid input for the corresponding hand-

wheel

Program Con-

tinuation:

Switch control OFF - ON.

4620 Invalid handwheel module for handwheel %1

Parameters: %1 = Handwheel module

Definitions: The handwheel module for handwheel %1 requested through machine date

$MN_HANDWHEEL_MODULE is not available for 802D systems. An 802D system is always

regarded as a module. For this reason, $MN_HANDWHEEL_MODULE = 1 must always be set for

handwheels directly linked with 802D systems.

Reaction: Interface signals are set.

Alarm display.

Remedy: Set machine date $MN_HANDWHEEL_MODULE = 1 for the corresponding handwheel.

Program Con-

tinuation:

Switch control OFF - ON.

4621 Invalid handwheel input for handwheel %1

Parameters: %1 = Handwheel input

Definitions: The handwheel input for handwheel %1 requested through machine date

$MN_HANDWHEEL_INPUT is not available for 802D systems. With 802D systems, a maximum of 2

handwheels can directly be linked.

Reaction: Interface signals are set.

Alarm display.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 391 392

Komentáře k této Příručce

Žádné komentáře

Siemens SINUMERIK 802D sl Specifikace Strana 37

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Siemens SINUMERIK 802D sl